• SLM系列无刷伺服电机选件
    SLM系列无刷伺服电机配置选项

    SLM Series Configuration Options A-F

    AAA = Frame Size
    BBB = Gear Reduction Ratio
    C = Shaft Type
    D = Connections
    E = Coating Options
    F = Brake Options

    GGG = Feedback Type

    Your choice of drive will dictate the appropriate feedback device for your situation. Options for feedback type include an array of absolute, analog and incremental encoders, as well as custom feedback alternatives.

    HHH = Motor Stator

    Motor Stator options are described with a 3-digit code. The first digit calls out the stack length, the second digit designates the rated bus voltage, and the third digit identifies the number of poles. Please refer to the mechanical/electrical specifications for motor torque and actuator rated force.

    Motor Stators (all 8 Pole and Class 180H)

    1A8 = 1 stack, 24 VDC *
    1B8 = 1 stack, 48 VDC *
    1C8 = 1 stack, 120 VDC *
    118 = 1 stack, 115 VRMS
    138 = 1 stack, 230 VRMS
    158 = 1 stack, 400 VRMS
    168 = 1 stack, 460 VRMS

     

    2A8 = 2 stack, 24 VDC *
    2B8 = 2 stack, 48 VDC *
    2C8 = 2 stack, 120 VDC *
    218 = 2 stack, 115 VRMS
    238 = 2 stack, 230 VRMS 
    258 = 2 stack, 400 VRMS
    268 = 2 stack, 460 VRMS

     

    3A8 = 3 stack, 24 VDC *
    3B8 = 3 stack, 48 VDC *
    3C8 = 3 stack, 120 VDC *
    318 = 3 stack, 115 VRMS
    338 = 3 stack, 230 VRMS
    358 = 3 stack, 400 VRMS
    368 = 3 stack, 460 VRMS 

     

    * Low voltage stators may be limited to less than catalog rated torque and/or speed. Please contact your local sales representative when ordering this option.

    II = Motor Speed Options

    All Exlar T-LAM™ motors and actuators have a standard motor speed designator (described below). The designator represents the standard base speed of the motor for the selected bus voltage.

    DesignatorBase SpeedMotor Series
    -505000 rpmSLM060
    -404000 rpmSLM075, SLM090
    -303000 rpmSLM115
    -242400 rpmSLM142, SLM180
    -01 … -99specialized speed *

     

    Please note that Exlar can manufacture its T-LAM products with specialized base speeds to exactly match your application requirements. This capability allows you to get the required torque and optimal speed for your application, while using the minimum amount of current from your amplifier.

    The callout for a special speed is configured in the model number by using a two-digit code from 01 through 99. These codes represent the number, in hundreds, of rpm that is the base speed for the motor.

    For example, a SLG090-010-KCGS-AB1-138-40 motor has a 4000 rpm standard winding. To specify a 3300 rpm winding, change the last two digits in the model number from 40 to 33. Similarly, to specify a 5000 rpm winding, you would change the last two digits from 40 to 50, and so on.

    Note: It is not possible to produce every possible speed for each motor at each voltage. *

    有关第1类认证的说明请点击此处

     

     

    有关第1类认证的说明请点击此处

    执行器电缆和连接

    Exlar执行器的IP等级

  • SLG / SLM Class 1,Division 2可选选项
    SLG / SLM 1类,2分区配置选项

    SLM/SLG Class I Division 2 Configuration Options A-F

    AAA = Frame Size
    BBB = Gear Reduction Ratio
    C = Shaft Type
    D = Connections
    E = Coatings
    F = Brake

    GGG = Feedback Type

    Your choice of drive will dictate the appropriate feedback device for your situation. Options for feedback type include: absolute, analog and incremental encoders, as well as custom feedback alternatives.

    H = Motor Stacks (all 8 Pole and Class 180H)

    1 = 1 stack3 = 3 stack
    2 = 2 stackx = Special

    I = Voltage Rating

    A = 24 VDC3 = 230 VRMS
    A = 48 VDC5 = 400 VRMS
    C = 120 VDC6 = 460 VRMS
    1 = 115 VRMSx = Special voltage rating (not to exceed 460 VRMS)

    Configuration Options J-K

    J = Motor Poles
    KK = Motor Speed

    SLG / SLM 1类,2分类机械选件

    NI = Non-incendive option

    Non-incendive option (required for Class I Division 2)

    SLG / SLM 1类,2分类特殊电机相关选项

    XM = Special Motor

    Special Motor Options should be listed as XM and must be approved by Exlar.*

    XL = Special (Non-Standard) Lubrication

    The XL option in the model number specifies some form of lubrication other than the standard provided by Exlar®, which is Mobilith SHC220. Special lubricants include other greases, such as JAX FG-2 food grade or Mobilgrease 28. Another non-standard option is oil cooling.*

    XF = Special Feedback

    Special Feedback Options should be listed as XF and must be approved by Exlar.*

    * 某些选项不适用于每个配置。有关其他详情和有效配置,请参阅 Exlar应用工程.

     

     

    有关第1类认证的说明请点击此处

    执行器电缆和连接

    Exlar执行器的IP等级