K Series:

  • K60
    • Performance Specifications

      K60 Mechanical Specifications

      Models KX KM 
      510510
      Screw Leadin0.19690.39370.19690.3937
      mm510510
      Maximum Force^2lbf13506751350675
      kN6363
      Life at Maximum Forcein x 10^61.618.20.44.5
      km41.7461.410.4115.3
      C_a (Dynamic Load Rating)lbf2738242117251525
      kN12.210.87.76.8
      Maximum Input Torque^1lbf-in53535353
      Nm6666
      Max Rated RPM @ Input ShaftRPM5000500050005000
      Maximum Linear Speed @
      Maximum Rated RPM
      in/sec16.432.816.432.8
      mm/sec417833417833
      1 - Input torque should be limited such that Max Force is not exceeded. For a parallel belt ratio, the input torque ratings must be divided by the belt ratio for allowable motor torque. The output force ratings remain the same.
      2 - Maximum allowable actuator–generated force that can be applied routinely. Exceeding this force may result in permanent damage to the actuator. For maximum allowable externally-applied axial forces, consult factory. For high force, short stroke applications, consult factory.

       

      K60 Intertias

       kg-m^2 (lbf-in-sec^2)kg-m^2 (lbf-in-sec^2)
      5 mm LeadAdd per 25 mm, 5 mm Lead
      Base Unit - Input Drive Shaft Only1.480 x 10^5 (1.31 x 10^4)1.022 x 10^6 (9.045 x 10^6)
      Inline Unit - w/Motor Coupling2.702 x 10^5 (2.39 x 10^4)1.022 x 10^6 (9.045 x 10^6)
      10 mm LeadAdd per 25 mm, 10 mm Lead
      Base Unit - Input Drive Shaft Only1.616 x 10^5 (1.43 x 10^4)1.173 x 10^6 (1.038 x 10^5)
      Inline Unit - w/Motor Coupling2.837 x 10^5 (2.51 x 10^4)1.173 x 10^6 (1.038 x 10^5)
      Parallel Drive Inertias (P10 Option)
      5 mm LeadAdd per 25 mm, 5 mm Lead
      1:1 Reduction Parallel Belt Drive (66 mm)4.339 x 10^5 (3.84 x 10^4)1.022 x 10^6 (9.045 x 10^6)
      1:1 Reduction Parallel Belt Drive (86 mm)7.378 x 10^5 (6.53 x 10^4)1.022 x 10^6 (9.045 x 10^6)
      1:1 Reduction Parallel Belt Drive (96 mm)8.564 x 10^5 (7.58 x 10^4)1.022 x 10^6 (9.045 x 10^6)
      2:1 Reduction Parallel Belt Drive (96 mm)7.095 x 10^5 (6.28 x 10^4)2.555 x 10^7 (2.261 x 1^6)
      10 mm LeadAdd per 25 mm, 10 mm Lead
      1:1 Reduction Parallel Belt Drive (66 mm)4.474 x 10^5 (3.96 x 10^4)1.173 x 10^6 (1.038 x 10^5)
      1:1 Reduction Parallel Belt Drive (86 mm)7.514 x 10^5 (6.65 x 10^4)1.173 x 10^6 (1.038 x 10^5)
      1:1 Reduction Parallel Belt Drive (96 mm)8.704 x 10^5 (7.70 x 10^4)1.173 x 10^6 (1.038 x 10^5)
      2:1 Reduction Parallel Belt Drive (96 mm)1.966 x 10^5 (1.74 x 10^4)2.931 x 10^7 (2.595 x 10^6)
      Parallel Drive Inertias (Smooth Motor Shaft Option)
      5 mm LeadAdd per 25 mm, 5 mm Lead
      1:1 Reduction Parallel Belt Drive (66 mm)6.015 x 10^5 (5.32 x 10^4)1.022 x 10^6 (9.045 x 10^6)
      1:1 Reduction Parallel Belt Drive (86 mm)1.103 x 10^4 (9.76 x 10^4)1.022 x 10^6 (9.045 x 10^6)
      1:1 Reduction Parallel Belt Drive (96 mm)2.176 x 10^4 (1.93 x 10^3)1.022 x 10^6 (9.045 x 10^6)
      2:1 Reduction Parallel Belt Drive (96 mm)8.768 x 10^5 (7.76 x 10^4)2.555 x 10^7 (2.261 x 10^6)
      10 mm LeadAdd per 25 mm, 10 mm Lead
      1:1 Reduction Parallel Belt Drive (66 mm)6.150 x 10^5 (5.44 x 10^4)1.173 x 10^6 (1.038 x 10^6)
      1:1 Reduction Parallel Belt Drive (86 mm)1.117 x 10^4 (9.88 x 10^4)1.173 x 10^6 (1.038 x 10^6)
      1:1 Reduction Parallel Belt Drive (96 mm)2.190 x 10^4 (1.94 x 10^3)1.173 x 10^6 (1.038 x 10^6)
      2:1 Reduction Parallel Belt Drive (96 mm)8.802 x 10^5 (7.79 x 10^4)2.931 x 10^7 (2.595 x 10^6)

       

      K60 Weights

       lbkg
      Base Actuator Weight (Zero Stroke)3.71.7
      Actuator Weight Adder (Per mm of Stroke)0.0170.008
      Adder for Inline (excluding motor)0.930.42
      Adder for Parallel Drive (excluding motor)1.60.73
      Adder for Front Flange0.930.42
      Adder for Rear Flange4.792.16
      Adder for Rear Clevis0.980.44
      Adder for Rear Eye0.670.30
      Adder for Front/Rear Angle Mounts0.540.24
      Adder for Two Trunnions0.720.33
      Adder for Two Foot Mounts10.45
    • Data Curves

      K60 Critical Speed

       

      Actuator Rated Speed (speed at which we have tested and rated the actuator)
      * With longer stroke length actuators, the rated speed of the actuator is determined by the critical speed

       


      K60 Maximum Radial

       


      K60 Rated Force

       

       

    • Estimated Life Time Curves

      KM60 Series Life Curves


      KX60 Series Life Curves

    • Ordering Guide

      To order a product from Exlar, a unique model mask (identification number) is required. The model mask is a string of characters that identifies the model, size, and configuration alternatives.

       

      K Order

       

      Product Selection Guidelines

      To facilitate your ordering process, feel free to print and complete this Exlar Application Worksheet, prior to contacting a Sales Representative in your area.

      Actuator Series

      KX = High Capacity Roller Screw
      KM = Standard Capacity Roller Screw

       

      AA = Actuator Frame Size

      60 = 60 mm (2.375 inches)
      75 = 75 mm (2.95 inches)
      90 = 90 mm (3.54 inches)

       

      BBBB = Stroke Length (mm)

      0150 = 150 mm
      0300 = 300 mm
      0600 = 600 mm
      0900 = 900 mm

       

      CC = Lead

      Linear motion per screw revolution

      05 = 5 mm (0.2 inch)
      10 = 10 mm (0.4 inch)

       

      D = Mounting Options

      N = None, Base Unit

       

      E = Rod End Options

      M = Male US standard thread
      A = Male metric
      F = Female US standard thread
      B = Female Metric thread

      FFF = Input Drive Provisions

      NMT = Drive Shaft Only, No Motor Mount
      ISC = Inline, includes shaft coupling

       

      Keyed Motor Shaft Options
      P10 = Parallel, 1:1 Belt Reduction, Keyed Motor Shaft
      P20 = Parallel, 2:1 Belt Reduction, Keyed Motor Shaft

       

      Smooth Motor Shaft Options
      S10 = Parallel, 1:1 Belt Reduction, Non-Keyed Motor Shaft
      S20 = Parallel, 2:1 Belt Reduction, Non-Keyed Motor Shaft

       

       

      GGG = Motor Mount Provisions 

      K60 Motor Mount Codes

      Bolt Circle Diameter (mm)Pilot Diameter (mm)Shaft Diameter (mm)Shaft Length (mm)Key Width (mm)Motor Mount Code
      634514385GEB
      6350a12364GEA
      686012304GFB
      686016485GFA
      705014305JGA
      705016305GGB
      705016375GGA
      756014305IHB
      906019406JKF
      907011304JKE
      907014305JKD
      90701635NAJKC
      907016405JKG
      907019406JKA
      955014305ELC
      956514305ELA
      956516305ELB
      1008010323IMD
      1008014305IMA
      1008014405JMC
      1008016405IMB
      1008019406IMC

       

      K75 Motor Mount Codes

      Bolt Circle Diameter (mm)Pilot Diameter (mm)Shaft Diameter (mm)Shaft Length (mm)Key Width (mm)Motor Mount Code
      686016485GFA
      705016405GGA
      756016485GHA
      857022566GIA
      906019406JKF
      907016405JKG
      907019406JKA
      1008014405JMC
      1008016405IMB
      1008019406IMC
      1008019556JMD
      1008022486GMA
      1159519406INA
      1159519556JNC
      1159522458JND
      115952270NAJNB
      1159524458JNA
      1159524508INB
      1309519406IPC
      1309524508IPD
      13011019406IPA
      13011024508IPB
      14511019406JQJ
      14511019555JQG
      14511019556JQK
      14511022558JQH
      14511022556JQF
      14511022708JQE

       

      K90 Motor Mount Codes

      Bolt Circle Diameter (mm)Pilot Diameter (mm)Shaft Diameter (mm)Shaft Length (mm)Key Width (mm)Motor Mount Code
      705016405GGA
      756016485GHA
      857022566GIA
      906019406JKF
      907016405JKG
      907019406JKA
      1008014405JMC
      1008016405IMB
      1008019406IMC
      1008019556JMD
      1008020406GMB
      1008022486GMA
      1159519406INA
      1159519556JNC
      1159522458JND
      115952270NAJNB
      1159524458JNA
      1159524508INB
      1309519406IPC
      1309524508IPD
      13011019406IPA
      13011024508IPB
      14511019406JQJ
      14511019555JQG
      14511019556JQK
      14511022558JQH
      14511022556JQF
      14511022708JQE
      14511024558JQD

      MM = Mechanical Options

      L1 = One N.O., PNP
      L2 = Two N.C., PNP
      L3 = One N.O. PNP & two N.C., PNP
      L4 = One N.O., NPN
      L5 = Two N.C., NPN
      L6 = One N.O., NPN & two N.C., NPN

       

      For extended temperature operation consult factory for model number.

       

  • K75
    • Performance Specifications

      K75 Mechanical Specifications

      Models KX KM 
      510510
      Screw Leadin0.19690.39370.19690.3937
      mm510510
      Maximum Force^2lbf2500125025001250
      kN11.15.611.15.6
      Life at Maximum Forcein x 10^62.422.60.65.6
      km60.7573.315.2143.5
      C_a (Dynamic Load Rating)lbf5746482036203036
      kN25.621.416.113.5
      Maximum Input Torque^1lbf-in98989898
      Nm11111111
      Max Rated RPM @ Input ShaftRPM4000400040004000
      Maximum Linear Speed @
      Maximum Rated RPM
      in/sec13.126.213.126.2
      mm/sec333666333666
      1 - Input torque should be limited such that Max Force is not exceeded. For a parallel belt ratio, the input torque ratings must be divided by the belt ratio for allowable motor torque. The output force ratings remain the same.
      2 - Maximum allowable actuator–generated force that can be applied routinely. Exceeding this force may result in permanent damage to the actuator. For maximum allowable externally-applied axial forces, consult factory. For high force, short stroke applications, consult factory.

       

      K75 Inertias

       kg-m^2 (lbf-in-sec^2)kg-m^2 (lbf-in-sec^2)
      5 mm LeadAdd per 25 mm, 5 mm Lead
      Base Unit - Input Drive Shaft Only9.26 x 10^5 (8.20 x 10^4)3.13 x 10^6 (2.77 x 10^5)
      Inline Unit - w/Motor Coupling1.25 x 10^4 (1.11 x 10^3)3.13 x 10^6 (2.77 x 10^5)
      10 mm LeadAdd per 25 mm, 10 mm Lead
      Base Unit - Input Drive Shaft Only9.48 x 10^5 (8.39 x 10^4)3.32 x 10^6 (2.94 x 10^5)
      Inline Unit - w/Motor Coupling1.44 x 10^4 (1.28 x 10^3)3.32 x 10^6 (2.94 x 10^5)
      Parallel Drive Inertias (P10 Option)
      5 mm LeadAdd per 25 mm, 5 mm Lead
      1:1 Reduction Parallel Belt Drive (86 mm)2.29 x 10^4 (2.03 x 10^3)3.13 x 10^6 (2.77 x 10^5)
      1:1 Reduction Parallel Belt Drive (96 mm)3.19 x 10^4 (2.82 x 10^3)3.13 x 10^6 (2.77 x 10^5)
      1:1 Reduction Parallel Belt Drive (130 mm)5.96 x 10^4 (5.28 x 10^3)3.13 x 10^6 (2.77 x 10^5)
      2:1 Reduction Parallel Belt Drive (130 mm)2.82 x 10^4 (2.50 x 10^3)7.83 x 10^7 (6.93 x 10^6)
      10 mm LeadAdd per 25 mm, 10 mm Lead
      1:1 Reduction Parallel Belt Drive (86 mm)2.31 x 10^4 (2.05 x 10^3)3.32 x 10^6 (2.94 x 10^5)
      1:1 Reduction Parallel Belt Drive (96 mm)3.21 x 10^4 (2.84 x 10^3)3.32 x 10^6 (2.94 x 10^5)
      1:1 Reduction Parallel Belt Drive (130 mm)5.98 x 10^4 (5.30 x 10^3)3.32 x 10^6 (2.94 x 10^5)
      2:1 Reduction Parallel Belt Drive (130 mm)2.83 x 10^4 (2.51 x 10^3)8.30 x 10^7 (7.36 x 10^6)
      Parallel Drive Inertias (Smooth Motor Shaft Option)
      5 mm LeadAdd per 25 mm, 5 mm Lead
      1:1 Reduction Parallel Belt Drive (86 mm)2.84 x 10^4 (2.51 x 10^3)3.13 x 10^6 (2.77 x 10^5)
      1:1 Reduction Parallel Belt Drive (96 mm)4.25 x 10^4 (3.76 x 10^3)3.13 x 10^6 (2.77 x 10^5)
      1:1 Reduction Parallel Belt Drive (130 mm)7.33 x 10^4 (6.48 x 10^3)3.13 x 10^6 (2.77 x 10^5)
      2:1 Reduction Parallel Belt Drive (130 mm)3.32 x 10^4 (2.94 x 10^3)7.83 x 10^7 (6.93 x 10^6)
      10 mm LeadAdd per 25 mm, 10 mm Lead
      1:1 Reduction Parallel Belt Drive (86 mm)2.86 x 10^4 (2.53 x 10^3)3.32 x 10^6 (2.94 x 10^5)
      1:1 Reduction Parallel Belt Drive (96 mm)4.27 x 10^4 (3.78 x 10^3)3.32 x 10^6 (2.94 x 10^5)
      1:1 Reduction Parallel Belt Drive (130 mm)7.35 x 10^4 (6.50 x 10^3)3.32 x 10^6 (2.94 x 10^5)
      2:1 Reduction Parallel Belt Drive (130 mm)3.33 x 10^4 (2.94 x 10^3)8.30 x 10^7 (7.35 x 10^6)

       

      K75 Weights

       lbkg
      Base Actuator Weight (Zero Stroke)6.753.06
      Actuator Weight Adder (Per mm of Stroke)0.02350.0107
      Adder for Inline (excluding motor)2.461.12
      Adder for Parallel Drive (excluding motor)4.061.84
      Adder for Front Flange1.910.87
      Adder for Rear Flange2.491.13
      Adder for Rear Clevis1.850.84
      Adder for Rear Eye1.850.84
      Adder for Front/Rear Angle Mounts1.370.62
      Adder for Two Trunnions1.560.71
      Adder for Two Foot Mounts2.471.12
    • Data Curves

      K75 Critical Speed

       

       

      Actuator Rated Speed (speed at which we have tested and rated the actuator)
      * With longer stroke length actuators, the rated speed of the actuator is determined by the critical speed

       


      K75 Maximum Radial

       


      K75 Rated Force

       

       

    • Estimated Life Time Curves

      KM75 Series Life Curves


      KX75 Series Life Curves

    • Ordering Guide

      To order a product from Exlar, a unique model mask (identification number) is required. The model mask is a string of characters that identifies the model, size, and configuration alternatives.

       

      K Order

       

      Product Selection Guidelines

      To facilitate your ordering process, feel free to print and complete this Exlar Application Worksheet, prior to contacting a Sales Representative in your area.

      Actuator Series

      KX = High Capacity Roller Screw
      KM = Standard Capacity Roller Screw

       

      AA = Actuator Frame Size

      60 = 60 mm (2.375 inches)
      75 = 75 mm (2.95 inches)
      90 = 90 mm (3.54 inches)

       

      BBBB = Stroke Length (mm)

      0150 = 150 mm
      0300 = 300 mm
      0600 = 600 mm
      0900 = 900 mm

       

      CC = Lead

      Linear motion per screw revolution

      05 = 5 mm (0.2 inch)
      10 = 10 mm (0.4 inch)

       

      D = Mounting Options

      N = None, Base Unit

       

      E = Rod End Options

      M = Male US standard thread
      A = Male metric
      F = Female US standard thread
      B = Female Metric thread

      FFF = Input Drive Provisions

      NMT = Drive Shaft Only, No Motor Mount
      ISC = Inline, includes shaft coupling

       

      Keyed Motor Shaft Options
      P10 = Parallel, 1:1 Belt Reduction, Keyed Motor Shaft
      P20 = Parallel, 2:1 Belt Reduction, Keyed Motor Shaft

       

      Smooth Motor Shaft Options
      S10 = Parallel, 1:1 Belt Reduction, Non-Keyed Motor Shaft
      S20 = Parallel, 2:1 Belt Reduction, Non-Keyed Motor Shaft

       

       

      GGG = Motor Mount Provisions 

      K60 Motor Mount Codes

      Bolt Circle Diameter (mm)Pilot Diameter (mm)Shaft Diameter (mm)Shaft Length (mm)Key Width (mm)Motor Mount Code
      634514385GEB
      6350a12364GEA
      686012304GFB
      686016485GFA
      705014305JGA
      705016305GGB
      705016375GGA
      756014305IHB
      906019406JKF
      907011304JKE
      907014305JKD
      90701635NAJKC
      907016405JKG
      907019406JKA
      955014305ELC
      956514305ELA
      956516305ELB
      1008010323IMD
      1008014305IMA
      1008014405JMC
      1008016405IMB
      1008019406IMC

       

      K75 Motor Mount Codes

      Bolt Circle Diameter (mm)Pilot Diameter (mm)Shaft Diameter (mm)Shaft Length (mm)Key Width (mm)Motor Mount Code
      686016485GFA
      705016405GGA
      756016485GHA
      857022566GIA
      906019406JKF
      907016405JKG
      907019406JKA
      1008014405JMC
      1008016405IMB
      1008019406IMC
      1008019556JMD
      1008022486GMA
      1159519406INA
      1159519556JNC
      1159522458JND
      115952270NAJNB
      1159524458JNA
      1159524508INB
      1309519406IPC
      1309524508IPD
      13011019406IPA
      13011024508IPB
      14511019406JQJ
      14511019555JQG
      14511019556JQK
      14511022558JQH
      14511022556JQF
      14511022708JQE

       

      K90 Motor Mount Codes

      Bolt Circle Diameter (mm)Pilot Diameter (mm)Shaft Diameter (mm)Shaft Length (mm)Key Width (mm)Motor Mount Code
      705016405GGA
      756016485GHA
      857022566GIA
      906019406JKF
      907016405JKG
      907019406JKA
      1008014405JMC
      1008016405IMB
      1008019406IMC
      1008019556JMD
      1008020406GMB
      1008022486GMA
      1159519406INA
      1159519556JNC
      1159522458JND
      115952270NAJNB
      1159524458JNA
      1159524508INB
      1309519406IPC
      1309524508IPD
      13011019406IPA
      13011024508IPB
      14511019406JQJ
      14511019555JQG
      14511019556JQK
      14511022558JQH
      14511022556JQF
      14511022708JQE
      14511024558JQD

      MM = Mechanical Options

      L1 = One N.O., PNP
      L2 = Two N.C., PNP
      L3 = One N.O. PNP & two N.C., PNP
      L4 = One N.O., NPN
      L5 = Two N.C., NPN
      L6 = One N.O., NPN & two N.C., NPN

       

      For extended temperature operation consult factory for model number.

       

  • K90
    • Performance Specifications

      K90 Mechanical Specifications

      Models KM KX 
      510510
      Screw Leadin0.19690.39370.19690.3937
      mm510510
      Maximum Force^2lbf3500175035001750
      kN15.67.815.67.8
      Life at Maximum Forcein x 10^61.822.67.190.4
      km44.9573.8179.62295
      C_a (Dynamic Load Rating)lbf727567501154810715
      kN32.43051.447.7
      Maximum Input Torque^1lbf-in137137137137
      Nm16161616
      Max Rated RPM @ Input ShaftRPM3000300030003000
      Maximum Linear Speed @
      Maximum Rated RPM
      in/sec9.819.79.819.7
      mm/sec250500250500
      1 - Input torque should be limited such that Max Force is not exceeded. For a parallel belt ratio, the input torque ratings must be divided by the belt ratio for allowable motor torque. The output force ratings remain the same.
      2 - Maximum allowable actuator–generated force that can be applied routinely. Exceeding this force may result in permanent damage to the actuator. For maximum allowable externally-applied axial forces, consult factory. For high force, short stroke applications, consult factory.

       

      K90 Inertias

       kg-m^2 (lbf-in-sec^2)kg-m^2 (lbf-in-sec^2)
      5 mm LeadAdd per 25 mm, 5 mm Lead
      Base Unit - Input Drive Shaft Only2.97 x 10^4 (2.63 x 10^3)1.11 x 10^5 (9.80 x 10^5)
      Inline Unit - w/Motor Coupling3.84 x 10^4 (3.40 x 10^3)1.11 x 10^5 (9.80 x 10^5)
      10 mm LeadAdd per 25 mm, 10 mm Lead
      Base Unit - Input Drive Shaft Only3.00 x 10^4 (2.66 x 10^3)1.13 x 10^5 (1.00 x 10^4)
      Inline Unit - w/Motor Coupling3.87 x 10^4 (3.43 x 10^3)1.13 x 10^5 (1.00 x 10^4)
      Parallel Drive Inertias (P10 Option)
      5 mm LeadAdd per 25 mm, 5 mm Lead
      1:1 Reduction Parallel Belt Drive (96 mm)5.12 x 10^4 (4.53 x 10^3)1.11 x 10^5 (9.80 x 10^5)
      1:1 Reduction Parallel Belt Drive (130 mm)7.98 x 10^4 (7.07 x 10^3)1.11 x 10^5 (9.80 x 10^5)
      2:1 Reduction Parallel Belt Drive (130 mm)3.41 x 10^4 (3.02 x 10^3)2.77 x 10^6 (2.45 x 10^5)
      10 mm LeadAdd per 25 mm, 10 mm Lead
      1:1 Reduction Parallel Belt Drive (96 mm)5.15 x 10^4 (4.56 x 10^3)1.13 x 10^5 (1.00 x 10^4)
      1:1 Reduction Parallel Belt Drive (130 mm)8.02 x 10^4 (7.10 x 10^3)1.13 x 10^5 (1.00 x 10^4)
      2:1 Reduction Parallel Belt Drive (130 mm)3.42 x 10^4 (3.03 x 10^3)2.82 x 10^6 (2.50 x 10^5)
      Parallel Drive Inertias (Smooth Motor Shaft Option)
      5 mm LeadAdd per 25 mm, 5 mm Lead
      1:1 Reduction Parallel Belt Drive (96 mm)6.18 x 10^4 (5.47 x 10^3)1.11 x 10^5 (9.80 x 10^5)
      1:1 Reduction Parallel Belt Drive (130 mm)9.35 x 10^4 (8.27 x 10^3)1.11 x 10^5 (9.80 x 10^5)
      2:1 Reduction Parallel Belt Drive (130 mm)3.91 x 10^4 (3.46 x 10^3)2.77 x 10^6 (2.45 x 10^5)
      10 mm LeadAdd per 25 mm, 10 mm Lead
      1:1 Reduction Parallel Belt Drive (96 mm)6.21 x 10^4 (5.50 x 10^3)1.13 x 10^5 (1.00 x 10^4)
      1:1 Reduction Parallel Belt Drive (130 mm)9.38 x 10^4 (8.30 x 10^3)1.13 x 10^5 (1.00 x 10^4)
      2:1 Reduction Parallel Belt Drive (130 mm)3.92 x 10^4 (3.47 x 10^3)2.82 x 10^6 (2.50 x 10^5)

       

      K90 Weights

       lbkg
      Base Actuator Weight (Zero Stroke)11.965.42
      Actuator Weight Adder (Per mm of Stroke)0.03660.016
      Adder for Inline (excluding motor)3.351.51
      Adder for Parallel Drive (excluding motor)5.82.62
      Adder for Front Flange3.41.54
      Adder for Rear Flange6.312.86
      Adder for Rear Clevis3.211.45
      Adder for Rear Eye2.491.13
      Adder for Front/Rear Angle Mounts1.970.9
      Adder for Two Trunnions1.7680.8
      Adder for Two Foot Mounts3.781.71
    • Data Curves

      K90 Critical Speed

       

       

      Actuator Rated Speed (speed at which we have tested and rated the actuator)
      * With longer stroke length actuators, the rated speed of the actuator is determined by the critical speed

       


      K90 Maxium Radial


      K90 Rated Force

       

       

    • Estimated Life Time Curves

      KM90 Series Life Curves


      KX90 Series Life Curves

    • Ordering Guide

      To order a product from Exlar, a unique model mask (identification number) is required. The model mask is a string of characters that identifies the model, size, and configuration alternatives.

       

      K Order

       

      Product Selection Guidelines

      To facilitate your ordering process, feel free to print and complete this Exlar Application Worksheet, prior to contacting a Sales Representative in your area.

      Actuator Series

      KX = High Capacity Roller Screw
      KM = Standard Capacity Roller Screw

       

      AA = Actuator Frame Size

      60 = 60 mm (2.375 inches)
      75 = 75 mm (2.95 inches)
      90 = 90 mm (3.54 inches)

       

      BBBB = Stroke Length (mm)

      0150 = 150 mm
      0300 = 300 mm
      0600 = 600 mm
      0900 = 900 mm

       

      CC = Lead

      Linear motion per screw revolution

      05 = 5 mm (0.2 inch)
      10 = 10 mm (0.4 inch)

       

      D = Mounting Options

      N = None, Base Unit

       

      E = Rod End Options

      M = Male US standard thread
      A = Male metric
      F = Female US standard thread
      B = Female Metric thread

      FFF = Input Drive Provisions

      NMT = Drive Shaft Only, No Motor Mount
      ISC = Inline, includes shaft coupling

       

      Keyed Motor Shaft Options
      P10 = Parallel, 1:1 Belt Reduction, Keyed Motor Shaft
      P20 = Parallel, 2:1 Belt Reduction, Keyed Motor Shaft

       

      Smooth Motor Shaft Options
      S10 = Parallel, 1:1 Belt Reduction, Non-Keyed Motor Shaft
      S20 = Parallel, 2:1 Belt Reduction, Non-Keyed Motor Shaft

       

       

      GGG = Motor Mount Provisions 

      K60 Motor Mount Codes

      Bolt Circle Diameter (mm)Pilot Diameter (mm)Shaft Diameter (mm)Shaft Length (mm)Key Width (mm)Motor Mount Code
      634514385GEB
      6350a12364GEA
      686012304GFB
      686016485GFA
      705014305JGA
      705016305GGB
      705016375GGA
      756014305IHB
      906019406JKF
      907011304JKE
      907014305JKD
      90701635NAJKC
      907016405JKG
      907019406JKA
      955014305ELC
      956514305ELA
      956516305ELB
      1008010323IMD
      1008014305IMA
      1008014405JMC
      1008016405IMB
      1008019406IMC

       

      K75 Motor Mount Codes

      Bolt Circle Diameter (mm)Pilot Diameter (mm)Shaft Diameter (mm)Shaft Length (mm)Key Width (mm)Motor Mount Code
      686016485GFA
      705016405GGA
      756016485GHA
      857022566GIA
      906019406JKF
      907016405JKG
      907019406JKA
      1008014405JMC
      1008016405IMB
      1008019406IMC
      1008019556JMD
      1008022486GMA
      1159519406INA
      1159519556JNC
      1159522458JND
      115952270NAJNB
      1159524458JNA
      1159524508INB
      1309519406IPC
      1309524508IPD
      13011019406IPA
      13011024508IPB
      14511019406JQJ
      14511019555JQG
      14511019556JQK
      14511022558JQH
      14511022556JQF
      14511022708JQE

       

      K90 Motor Mount Codes

      Bolt Circle Diameter (mm)Pilot Diameter (mm)Shaft Diameter (mm)Shaft Length (mm)Key Width (mm)Motor Mount Code
      705016405GGA
      756016485GHA
      857022566GIA
      906019406JKF
      907016405JKG
      907019406JKA
      1008014405JMC
      1008016405IMB
      1008019406IMC
      1008019556JMD
      1008020406GMB
      1008022486GMA
      1159519406INA
      1159519556JNC
      1159522458JND
      115952270NAJNB
      1159524458JNA
      1159524508INB
      1309519406IPC
      1309524508IPD
      13011019406IPA
      13011024508IPB
      14511019406JQJ
      14511019555JQG
      14511019556JQK
      14511022558JQH
      14511022556JQF
      14511022708JQE
      14511024558JQD

      MM = Mechanical Options

      L1 = One N.O., PNP
      L2 = Two N.C., PNP
      L3 = One N.O. PNP & two N.C., PNP
      L4 = One N.O., NPN
      L5 = Two N.C., NPN
      L6 = One N.O., NPN & two N.C., NPN

       

      For extended temperature operation consult factory for model number.