• SLG Series Gearmotor Options
    SLG Series Gearmotor Configuration Options

    SLG Series Configuration Options A-F

    AAA = Frame Size
    BB = Gear Reduction Ratio
    C = Shaft Type
    D = Connections
    E = Coatings
    F = Brake

    GGG = Feedback Type

    Your choice of drive will dictate the appropriate feedback device for your situation. Options for feedback type include an array of absolute, analog and incremental encoders, as well as custom feedback alternatives.

    HHH = Motor Stator

    Motor Stator options are described with a 3-digit code. The first digit calls out the stack length, the second digit designates the rated bus voltage, and the third digit identifies the number of poles. Please refer to the mechanical/electrical specifications for motor torque and actuator rated force.

    Motor Stators (all 8 Pole and Class 180H)

    1A8 = 1 stack, 24 VDC *
    1B8 = 1 stack, 48 VDC *
    1C8 = 1 stack, 120 VDC *
    118 = 1 stack, 115 VRMS
    138 = 1 stack, 230 VRMS
    158 = 1 stack, 400 VRMS
    168 = 1 stack, 460 VRMS

     

    2A8 = 2 stack, 24 VDC *
    2B8 = 2 stack, 48 VDC *
    2C8 = 2 stack, 120 VDC
    218 = 2 stack, 115 VRMS*
    238 = 2 stack, 230 VRMS
    258 = 2 stack, 400 VRMS
    268 = 2 stack, 460 VRMS

     

    3A8 = 3 stack, 24 VDC *
    3B8 = 3 stack, 48 VDC *
    3C8 = 3 stack, 120 VDC *
    318 = 3 stack, 115 VRMS
    338 = 3 stack, 230 VRMS
    358 = 3 stack, 400 VRMS
    368 = 3 stack, 460 VRMS

     

    * Low voltage stators may be limited to less than catalog rated torque and/or speed. Please contact your local sales representative when ordering this option.

    II = Motor Speed Options

    All Exlar T-LAM™ motors and actuators have a standard motor speed designator (described below). The designator represents the standard base speed of the motor for the selected bus voltage.

    Designator  Base SpeedMotor Series
    -505000 rpmSLG060
    -404000 rpmSLG075
    -404000 rpm SLG090
    -303000 rpm SLG115
    -01 … -99 specialized speed *

     

    Please note that Exlar can manufacture its T-LAM products with specialized base speeds to exactly match your application requirements. This capability allows you to get the required torque and optimal speed for your application, while using the minimum amount of current from your amplifier.

    The callout for a special speed is configured in the model number by using a two-digit code from 01 through 99. These codes represent the number, in hundreds, of rpm that is the base speed for the motor.

    For example, a SLG090-010-KCGS-AB1-138-40 motor has a 4000 rpm standard winding. To specify a 3300 rpm winding, change the last two digits in the model number from 40 to 33. Similarly, to specify a 5000 rpm winding, you would change the last two digits from 40 to 50, and so on.

    Note: It is not possible to produce every possible speed for each motor at each voltage. *

    SLG Series Gearmotor Mechanical Options

    HW = Manual Drive – Handwheel

    A manual drive handwheel installed on the side of the actuator. Includes an engage/disengage lever that controls an interrupt switch. This lever is not tied to the motor and must be engaged/disengaged, before operating the motor. Not available on all products and may not be available with a holding brake. *

    *Some options are not available with every configuration. For options or specials not listed above or for extended temperature operation, please consult Exlar Applications Engineering.

     

     

    For a description of Class 1 Certifications click here

    Cables and Connections

    IP Ratings for Exlar Actuators

  • SLG/SLM Class 1, Division 2 Available Options
    SLG/SLM Class 1, Division 2 Configuration Options

    SLM/SLG Class I Division 2 Configuration Options A-F

    AAA = Frame Size
    BBB = Gear Reduction Ratio
    C = Shaft Type
    D = Connections
    E = Coatings
    F = Brake

    GGG = Feedback Type

    Your choice of drive will dictate the appropriate feedback device for your situation. Options for feedback type include: absolute, analog and incremental encoders, as well as custom feedback alternatives.

    H = Motor Stacks (all 8 Pole and Class 180H)

    1 = 1 stack3 = 3 stack
    2 = 2 stackx = Special

    I = Voltage Rating

    A = 24 VDC3 = 230 VRMS
    A = 48 VDC5 = 400 VRMS
    C = 120 VDC6 = 460 VRMS
    1 = 115 VRMSx = Special voltage rating (not to exceed 460 VRMS)

    Configuration Options J-K

    J = Motor Poles
    KK = Motor Speed

    SLG/SLM Class 1, Division 2 Mechanical Options

    HW = Manual Drive – Handwheel

    A manual drive handwheel installed on the side of the actuator. Includes an engage/disengage lever that controls an interrupt switch. This lever is not tied to the motor and must be engaged/disengaged, before operating the motor. Not available on all products and may not be available with a holding brake. *

     

    RB = Rear Electric Brake

    This is a rear, internal holding brake. The rear brake is spring activated and electrically released.

    RD = Manual Drive – Simple Rear

    This option provides a hex shaft at the rear of the actuator for manual operation. The hex shaft is directly coupled to the motor and can be turned by hand with a compatible wrench. The hex shaft is enclosed by a sealed cap during operation. This option is not available w/absolute feedback. If the application requires a brake, discuss manual drive use with your local sales representative.

    SD = Manual Drive – Side Hex

    A manually operated side hex shaft installed at the rear of the actuator. The hex shaft is directly coupled to the motor and can be turned by hand using a compatible wrench. The hex shaft is sealed with a cap during operation. This option may not be available with a holding brake. *

    SLG/SLM Class 1, Division 2 Special Housing Options

    SLM/SLG Class I Division 2 Special Housing Options

    EN = Electroless nickel plating
    SS = Stainless Steel Housing
    XH = Other special housing options
    P5 = IP65S environmental sealing
    HC = Type III Hard Coat Anodized, Class 1, no dye

    SLG/SLM Class 1, Division 2 Special Motor-Related Options

    XM = Special Motor

    Special Motor Options should be listed as XM and must be approved by Exlar.*

    XL = Special (Non-Standard) Lubrication

    The XL option in the model number specifies some form of lubrication other than the standard provided by Exlar®, which is Mobilith SHC220. Special lubricants include other greases, such as JAX FG-2 food grade or Mobilgrease 28. Another non-standard option is oil cooling.*

    XF = Special Feedback

    Special Feedback Options should be listed as XF and must be approved by Exlar.*

    *Some options are not available with every configuration. For options or specials not listed above or for extended temperature operation, please consult Exlar Applications Engineering.

     

     

    For a description of Class 1 Certifications click here

    Cables and Connections

    IP Ratings for Exlar Actuators